This program focuses on the manufacturer-specific requirements for the most popular domestic and import vehicle/sensor manufacturers. This program is designed to give the experienced technician more in-depth information regarding the identification, maintenance, reprogramming, and diagnostic procedures for all tire pressure monitoring systems.
Advanced TPMS is comprised of four modules:
Module 1 TPMS Identification - focuses on identifying different types of TPMS and how to differentiate between a low tire indicator and a malfunction indicator.
Module 2 TPMS Service Requirements - demonstrates how to identify the proper service pack for the sensor as well as the installation procedures for all types of sensors.
Module 3 TPMS Relearn Procedures - uses the TPMS Relearn Chart and common electronic relearn tools to explain the relearn requirements for the most popular domestic and import vehicles.
Module 4 TPMS Diagnostics - covers the necessary steps to identify and correct a malfunction with common electronic tools.
Basic Automotive Tire Service (ATS) is a 200 Level minimum skills training and certificate program that outlines and explains the guidelines for servicing passenger and light truck tire and wheel assemblies. It includes a DVD, Instructor's Guide (lesson plans), 1 Student Workbook and 1 Final Exam. Additional Workbooks and Exams can be ordered for each technician in need of training.
Basic ATS is comprised of ten modules:
Module 1Introduction Covers personal protective equipment and general shop safety.
Module 3Wheels & Fasteners Covers wheel and rim nomenclature as well as fastener and bolt hole identification.
Module 4Raising the Vehicle Addresses step-by-step procedures and safety guidelines for lifting a vehicle with an above-ground lift or floor jack and jack stands.
Module 5Tire/Wheel Assembly Removal Covers the procedures for removing the assembly from the vehicle including wheel locks and wheel covers.
Module 6Torque & Clamping Force Explains the relationship between torque and clamping force including lab tests that show the effects of lubricants.
Module 7RIST Stands for Remove, Inspect, Snug and Torque. This module covers the steps for wheel installation using the RIST procedure.
Module 8Demounting, Mounting & Inflation Covers the procedures for demounting, mounting and inflating tires on rims with valve stem and band-mounted sensors.
Module 9Balance and Run-out Addresses the basic principles of balance and run-out including the use of pin-plates to secure the assembly to the balancer.
Module 10Puncture Repair Covers the general industry guidelines for puncture repairs in passenger and light truck tires using one-piece and two-piece repair systems.
According to the Occupational Safety & Health Administration (OSHA) Regulation 29 CFR 1910.177, any employee that handles truck tires and wheels must receive safety training and demonstrate their ability to perform the necessary tasks. The Basic Commercial Tire Service (CTS) Training and Certificate Program is designed to meet the minimum federal training requirements for both new hires and experienced employees in need of documented training.
The Basic CTS Program includes 12 Modules and comes with a DVD, Instructor's Guide (lesson plans), 1 Student Workbook and 1 Final Exam Book. Additional Workbooks and Exams can be ordered for technicians in need of training.
Module 1Safety Includes personal protective equipment, lifting safety, and other topics like heat stroke and frostbite prevention.
Module 2Basic Tire Info Covers tire construction, sizing, nomenclature, inflation pressure, tread design and compound for different applications, speed rating and all special service ratings and identification.
Module 3Rims and Wheels Outlines the difference between rims and wheels including the nomenclature for both assemblies. It will also identify and address the different type of hub and drum assemblies for commercial vehicles.
Module 4OSHA Regulations The video includes the script for the OSHA Reg 29 CFR 1910.177 with images supporting the wording. The Workbook also includes the OSHA Demount/Mount and Rim Matching Charts.
Module 5Jacking and Lifting Outlines procedures for properly jacking, lifting and supporting trucks, tractors and trailers. It focuses on jack and jack stand identification adn operation as well as proper position of each when lifting one, two or three axles.
Module 6Torque An in-depth look at the relationship between torque and clamping force when installing wheels and rims.
Module 7Wheel End Safety Addresses wheel end fires, commercial vehicle inspection, wheel-off prevention and wheel end maintenance.
Module 8Hub-Pilot Wheels Puts the basic principles of the previous two modules to work with hub-pilot wheel removal as well as inspection and installation guidelines.
Module 9Stud-Pilot Wheels Focuses on stud-pilot wheel removal, inspection and installation.
Module 10Demountable Rims Addresses demountable rim removal, inspection and installation.
Module 11Single-Piece Dedicated to single-piece demount, mount and inflation procedures with an increased emphasis on disc wheel inspection, valve stem installation (including torque) and concentric bead seating techniques.
Module 12Multi-Piece Covers the basics for demounting, mounting and inflated 2- and 3-piece assemblies.
According to the Occupational Safety & Health Administration (OSHA) Regulation 29 CFR 1910.177, any employee that handles truck tires and wheels must receive safety training and demonstrate their ability to perform the necessary tasks. The Basic Commercial Tire Service (CTS) Training and Certificate Program is designed to meet the minimum federal training requirements for both new hires and experienced employees in need of documented training.
The Spanish Basic CTS Program includes 12 Modules and comes with a DVD, Instructor's Guide (lesson plans), 1 Student Workbook and 1 Final Exam Book. Additional Workbooks and Exams can be ordered for technicians in need of training.
The 3-hour video features 15 different modules that cover the basic safety guidelines for servicing OTR tires, wheels and rims in the field. The video is accompanied by a 200+ page workbook that features hundreds of four-color photos to outline the step-by-step procedures and various industry resources. Students that successfully complete the final exam will receive a TIA Certificate of Completion. Check out a 10 minute video trailer.
Basic ETS is comprised of 15 modules:
Module 1 – Introduction
Module 2 – Tires, Rims & Valves
Module 3 – Service Truck Operation
Module 4 – Site Preparation & Equipment Lifting Module 5 – Hydraulic Bead Breakers & Rams Module 6 – Service One-Piece on Machine Module 7 – Service Three-Piece on Machine Module 8 – Service Five-Piece on Machine Module 9 – Service Double Gutter on Machine Module 10 – Service One-Piece Loose Module 11 – Service Three-Piece Loose Module 12 – Service Five-Piece Loose Module 13 – Wheel & Rim Fastening Systems Module 14 – Install & Remove Wheel Fitment Module 15 – Install and Remove Rim Fitment
Please Note: In order to meet Part 46 MSHA requirements, companies must ensure that employees complete an 8-hour refresher course on an annual basis. Following the initial purchase of workbooks, companies can purchase separate Test Booklets a year later, and after the employees have completed the 8-hour classroom instruction, they can take the test and receive an updated Certificate and wallet ID card to reflect successful completion of the 8-hour refresher.
Each Basic Earthmover Tire Service (ETS) Kit includes two DVD's, one Workbook, and one Test Booklet. Each Workbook also comes with a separate Test Booklet. Students who successfully complete the final exam will receive a TIA Certificate of Completion and a wallet ID card.
(Shipping and handling additional.) Final pricing based on quantity purchased:
ETS additional Student Workbook (includes one Test Booklet)
Final pricing based on quantity purchased:
1-9 Non-Member Price: $195 Member Price: $95 10-19 Non-Member Price: $185 Member Price: $85 20+ Non-Member Price: $175 Member Price: $75
ETS Additional Test Booklet (does not include Student Workbook)
Final pricing based on quantity purchased:
1-9 Non-Member Price: $175 Member Price: $75 10-19 Non-Member Price: $165 Member Price: $65 20+ Non-Member Price: $150 Member Price: $50
The 3-hour video features 15 different modules that cover the basic safety guidelines for servicing OTR tires, wheels and rims in the field. The video is accompanied by a 200+ page workbook that features hundreds of four-color photos to outline the step-by-step procedures and various industry resources. Students that successfully complete the final exam will receive a TIA Certificate of Completion. Check out a 10 minute video trailer.
(Shipping and handling additional.) Final pricing based on quantity purchased:
ETS additional Student Workbook (includes one Test Booklet)
Final pricing based on quantity purchased: 1-9 Non-Member Price: $195 Member Price: $95 10-19 Non-Member Price: $185 Member Price: $85 20+ Non-Member Price: $175 Member Price: $75
ETS Additional Test Booklet (does not include Student Workbook)
Final pricing based on quantity purchased: 1-9 Non-Member Price: $175 Member Price: $75 10-19 Non-Member Price: $165 Member Price: $65 20+ Non-Member Price: $150 Member Price: $50
This program outlines and explains the guidelines for servicing farm, agricultural and construction tire and wheel assemblies. The Basic FTS Program includes 11 Modules, plus an Appendix, and comes with a DVD, Instructor's Guide, 1 Student Workbook and 1 Final Exam. Additional Workbooks and Exams can be ordered for technicians in need of training.
Module 1Introduction Covers the necessary PPE for servicing farm, agricultural and construction tires. It also addresses the primary hazards for technicians who service these assemblies so they understand the risks.
Module 2Tires Outlines the construction, nomenclature, sizing, service description, speed rating and load capacity molded on the sidewall.
Module 3Rims, Wheels and Valves Describes the different types of rims and wheels used on ag and construction equipment.
Module 4Service Truck Operation and Maintenance Covers every aspect of the service truck, especially the operation, inspection and maintenance of the crane and compressor. Techs will also learn the steps for conducting a proper pre-trip inspection.
Module 5Lifting the Machine Addresses the proper procedures for lifting different types of farm and construction equipment. Emphasis is placed on using the correct lifting points and utilizing cribbing or jack stands to support the weight of the machine during service.
Module 6Hydraulic Tool Operation and Maintenance Describes the different types of hydraulic tools that are used to service farm, ag and construction tires. Techs will learn how to operate and maintain the tools and the hydraulic pump.
Module 7Single Piece Demount, Mount & Inflate on Machine Outlines the procedures for demounting, mounting and inflating a single piece tubeless tire while it is still installed on the machine.
Module 8Single Piece Demount, Mount & Inflate off Machine Describes the procedures for demounting, mounting and inflating a single piece tubeless tire when it is loose and off the machine. Procedures for demounting, mounting and inflating a tube-type assembly are also covered in this module.
Module 9Dual Demount, Mount & Inflate Describes the procedures for demounting, mounting and inflating a single piece tubeless tire in a dual application.
Module 103-Piece Demount, Mount & Inflate on Machine Covers the procedures for demounting, mounting and inflating a tubeless tire on a 3-piece rim while it is still on the machine. Techs will also learn how to properly inspect the rim components to ensure they can be safely installed before the tire is inflated
Module 11Install and Remove Liquid Ballast Addresses the guidelines for installing and removing liquid ballast. It covers the basic procedures for using calcium chloride as ballast material and addresses the safety guidelines that should be followed.
Appendix Includes valuable info that techs can use in the field on a regular basis - Load Index Chart, Size Comparison Chart, Calcium Chart and Tire & Rim Association charts.
According to the Occupational Safety & Health Administration (OSHA) Regulation 29 CFR 1910.177, any employee that handles truck tires and wheels must receive safety training and demonstrate their ability to perform the necessary tasks. The Basic Commercial Tire Service (CTS) Training and Certificate Program is designed to meet the minimum federal training requirements for both new hires and experienced employees in need of documented training.
The Fleet OSHA Compliance Program includes 12 Modules and comes with a DVD, Instructor's Guide (lesson plans), 1 Student Workbook and 1 Final Exam Book. Additional Workbooks and Exams can be ordered for technicians in need of training.
Module 1Safety Includes personal protective equipment, lifting safety, and other topics like heat stroke and frostbite prevention.
Module 2Basic Tire Info Covers tire construction, sizing, nomenclature, inflation pressure, tread design and compound for different applications, speed rating and all special service ratings and identification.
Module 3Rims and Wheels Outlines the difference between rims and wheels including the nomenclature for both assemblies. It will also identify and address the different type of hub and drum assemblies for commercial vehicles.
Module 4OSHA Regulations The video includes the script for the OSHA Reg 29 CFR 1910.177 with images supporting the wording. The Workbook also includes the OSHA Demount/Mount and Rim Matching Charts.
Module 5Jacking and Lifting Outlines procedures for properly jacking, lifting and supporting trucks, tractors and trailers. It focuses on jack and jack stand identification adn operation as well as proper position of each when lifting one, two or three axles.
Module 6Torque An in-depth look at the relationship between torque and clamping force when installing wheels and rims.
Module 7Wheel End Safety Addresses wheel end fires, commercial vehicle inspection, wheel-off prevention and wheel end maintenance.
Module 8Hub-Pilot Wheels Puts the basic principles of the previous two modules to work with hub-pilot wheel removal as well as inspection and installation guidelines.
Module 9Stud-Pilot Wheels Focuses on stud-pilot wheel removal, inspection and installation.
Module 10Demountable Rims Addresses demountable rim removal, inspection and installation.
Module 11Single-Piece Dedicated to single-piece demount, mount and inflation procedures with an increased emphasis on disc wheel inspection, valve stem installation (including torque) and concentric bead seating techniques.
Module 12Multi-Piece Covers the basics for demounting, mounting and inflated 2- and 3-piece assemblies.
According to the Occupational Safety & Health Administration (OSHA) Regulation 29 CFR 1910.177, any employee that handles truck tires and wheels must receive safety training and demonstrate their ability to perform the necessary tasks. The Basic Commercial Tire Service (CTS) Training and Certificate Program is designed to meet the minimum federal training requirements for both new hires and experienced employees in need of documented training.
The Spanish Fleet OSHA Compliance Program includes 12 Modules and comes with a DVD, Instructor's Guide (lesson plans), 1 Student Workbook and 1 Final Exam Book. Additional Workbooks and Exams can be ordered for technicians in need of training.
Basic ITS focuses on pneumatic, solid resilient, press-on and polyurethane-filled tires used in industrial applications. It covers the service procedures for different types of tire and rim assemblies. The Basic ITS Program includes 11 Modules, and comes with a DVD, Instructor's Guide, 1 Student Workbook and 1 Final Exam. Additional Workbooks and Exams can be ordered for technicians in need of training.
Module 1Introduction Covers the required personal protective equipment (PPE) as well as the inflation equipment required by OSHA regulation 29 CFR 1910.177.
Module 2Tires Addresses the unique size designations for pneumatic, solid resilient and press-on tires and explains their differences to ensure the proper fitment is used on industrial machines.
Module 3Rims, Wheels and Hubs Describes the different types of rims, wheels and hubs that are used on pneumatic, solid and press-on tires. It also includes information on dimensions and explains how they are measured.
Module 4Hydraulic Press Operation & Maintenance Solid resilient and press-on tires require a specialized hydraulic press. This module explains the basic principles for press operation and covers the regular inspection and maintenance guidelines that should be followed.
Module 5Jacking & Lifting, Install and Remove Adresses the proper lifting and support procedures for different types of industrial equipment, and the steps for installing and removing different types of industrial tire assemblies.
Module 6Single-Piece Service Procedures While most tires used on single-piece rims are tubeless pneumatic, a special type of solid resilient tire is also used on a singlie-piece rim. This module addresses the service procedures for both types of tires on single-piece rims.
Module 7Two-Piece Service Procedures There are two types of two-piece rims used in industrial applications: traditional rim base with a side ring and bolt-together. This module covers the service procedures for pneumatic and solid resilient tires on both types of two-piece rims.
Module 8Three-Piece Service Procedures Focuses on pneumatic and solid resilient tires used on three-piece rims, and explains the step-by-step service procedures for standard three-piece rims and three-piece rims that include a bead seat stand.
Module 9Tube-Type/Tubeless Conversion Continental and Michelin have developed special systems that allow tubeless tires to be mounted on rims that typically require an innertube and flap. This module covers the installation procedures for both systems on two-piece and three-piece rims.
Module 10Press-On Demount/Mount Addresses how to use the unique tools and equipment used for demounting and mounting press-on tires on different types of hubs.
Module 11Poly Fill In applications where the flat proof qualities of solid resilient and press-on tires are needed but not available, standard tubeless and tube-type tires can be filled with polyurethane. This module covers the procedures and guidelines for installing polyurethane fill in standard tire and wheel assemblies.
The TIA OTR Mount/Demount Program covers eight tire mounting and demounting procedures on seven of the most common pieces of OTR equipment, using both bias and radial tires. With video technology, the program teaches vertical and horizontal mount and demount procedures for single-, three- and five-piece wheel and rim assemblies, and also includes a review of wheel and tire terminology.
By focusing on specific tire sizes and pieces of OTR equipment, TIA can provide valuable instruction on the most commonly used loaders, graders and articulating haul trucks. The tires and equipment include: 17.5-25s on a 142G grader; 37.25R35s on a 631E scraper; 35/65R33s on a 988 front end loader; 23.5R25s on an articulated haul truck; 40.00R57 rear duals on an 830E haul truck; and a 40.00R57 front tire on a 793 haul truck. Service vehicles in the OTR Program utilize both cranes and tire hands to reflect the latest technology and techniques available for handling the worlds largest tire and wheel assemblies.
A 140-page Program Book accompanies the video and becomes a valuable reference following the training. Additional Program Books are sold separately (OTRAB-200). TIAs OTR Mount/ Demount Training and Certificate Program represents the industrys most up-to-date educational program for instructing technicians on the safety guidelines for servicing multi-piece assemblies used on todays OTR equipment.
The 140-page OTR Program Book includes all of the material contained in the video and serves as a valuable reference in the field after training is completed. With its spiral binding and heavy-duty cover, the OTR Program Book better withstands the rigors of the OTR tire service environment.
Once the technician studies the Program Book, companies have the option of recognizing technician proficiency and achievement by administering the final exam. The TIA OTR Program Test includes a test booklet and answer sheet. Technicians that successfully complete the Test with a score of 70 percent or better receive a TIA Certificate of Completion.
TIAs TPMS Training Program is designed to provide
technicians with a basic understanding of how different types of systems
interact with the vehicle. It also includes the various types of service
that technicians will need to perform in order to maintain the system.
Since most TPMS utilize a valve stem sensor and many include run-flat
tires, special attention is given to the step-by-step procedures for handling
these assemblies.
The TPMS Training Program also covers recalibration guidelines for many
popular models and includes an appendix with relearn summaries and installation
torque values for valve stem sensors. Each kit includes a 50-minute Video
and DVD as well as a 120-page workbook that one technician can use to
receive a TIA Certificate of Completion.
Other Related Products:
• Student Workbook must be ordered for every technician going through the Training Program TPMSAB-200.
The TPMS Student Workbook must be ordered for every technician going through the Training Program. The workbook follows along with the video and includes the 40-question final exam, which will be sent in to TIA for grading. Those that pass the exam receive a TIA Certificate of Completion.
TIAs Spanish TPMS Training Program is designed to provide
technicians with a basic understanding of how different types of systems
interact with the vehicle. It also includes the various types of service
that technicians will need to perform in order to maintain the system.
Since most TPMS utilize a valve stem sensor and many include run-flat
tires, special attention is given to the step-by-step procedures for handling
these assemblies.
The Spanish TPMS Training Program also covers recalibration guidelines for many
popular models and includes an appendix with relearn summaries and installation
torque values for valve stem sensors. Each kit includes a 50-minute Video
and DVD as well as a 120-page workbook that one technician can use to
receive a TIA Certificate of Completion.
Other Related Products:
• Student Workbook must be ordered for every technician going through the Training Program.
The TPMS Student Workbook must be ordered for every technician
going through the Training Program. The Spanish workbook follows along with the
video and includes the 40-question final exam, which will be sent in to
TIA for grading. Those that pass the exam receive a TIA Certificate of
Completion.